Micromod MOD: 30ML Operation and Template Setup Instrukcja Użytkownika Pobierz pdf (Strona 27)

MOD 30ML Operation

SETUP

2-17

Table 8. User Compound Template Configuration (Cont’d)

Step Step Description Line 1 Line 2 Line 6 Entry Description

Steps 8E3A through F only presented when there is a remote setpoint input

8E3A Local Setpoint Enable

∇ ∆ change value, ENT enters

NXT, PRV change step

LOCAL SETPOINT ENABLE

Enable or Disable a local setpoint

value

8E3B Setpoint Ratio

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT RATIO DISABLE

Enable or Disable a remote

setpoint ratio value

8E3C Setpoint Ratio Value

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT RATIO 1.000

Initial ratio value.

Auto balance calculation is:

(Active Setpoint - Bias) / Rem SP

8E3D Setpoint Bias

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT BIAS DISABLE

Enable or Disable a remote

setpoint bias value

8E3E Setpoint Bias Value

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT BIAS 0.000

Initial bias value.

Auto balance calculation is:

Active Setpoint - (Rem SP * Ratio)

8E3F Setpoint Balance

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT BALANCE AUTO RAT

AUTO RAT, Ratio value calculated

to balance transition to remote.

STANDARD, Ratio and Bias use

the operator values.

AUTO BIA, Bias value calculated to

balance transition to remote.

Setpoint (Cont’d)

8E4 Setpoint Low Limit

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT LO LIMIT 0.000

Setpoint values to the PID

algorithm are limited to this number

or above.

8E5 Setpoint High Limit

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT HI LIMIT 100.000

Setpoint values to the PID

algorithm are limited to this number

or below.

8E6 Setpoint Restart Mode

∇ ∆ change value, ENT enters

NXT, PRV change step

RESTART SP MODE PREVIOUS

Previous (requires setting initial SP

Mode), Local or Remote

Local only for Master Controller.

8E7 Setpoint Initial Mode

∇ ∆ change value, ENT enters

NXT, PRV change step

INITIAL SP MODE LOCAL

Local or Remote

Local only for Master Controller.

8E8 Setpoint Restart Value

∇ ∆ change value, ENT enters

NXT, PRV change step

RESTART SP VAL PREVIOUS

Previous (enter an Initial Value) or

Preset (enter a Restart Value).

8E9 Setpoint Restart Preset Value

∇ ∆ change value, ENT enters

NXT, PRV change step

RESTART VALUE 0.0

Enter restart value for setpoint.

8E10 Setpoint Initial Value

∇ ∆ change value, ENT enters

NXT, PRV change step

INITIAL VALUE 0.0

Enter initial value for setpoint.

8E11 Setpoint Tracking

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT TRACK DISABLE

Enable or Disable

When active, setpoint tracks input

while in manual.

8E12 Setpoint (Exit)

∆ moves up to Step 8E

NXT, PRV change step

COMPOUND

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 83 84

Komentarze do niniejszej Instrukcji

Brak uwag

Micromod MOD: 30ML Operation and Template Setup Instrukcja Użytkownika Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Micromod MOD: 30ML Operation and Template Setup